Level 5 · Perfume Mathematics and Formula Design

Precision and Rounding in a Formula

A math drill: match a formula's figures to what your balance can weigh, find the rounding error of small weighings, and keep totals exact.

In short

A formula's figures are only as good as your balance. If the formula asks for 0.0333 g and your balance reads to 0.01 g, the record describes something you cannot make. This drill teaches three habits: work out the rounding error of each weighing, use a dilution when a weighing is too small to be accurate, and round a formula so that it still adds up to its total, with the leftover assigned by a rule you write down.

What you will learn

  • Calculate the relative rounding error of a weighing
  • Choose a dilution that makes a small weighing accurate enough
  • Round a formula so it still adds up to its stated total

Before this lesson: Stock Solutions in Practice

The rounding error of a weighing

A balance reading is uncertain by about half its readability. On a 0.01 g balance that is ±0.005 g, which matters more the smaller the weighing:

Relative rounding error on a 0.01 g balance (±0.005 g).
WeighingRelative error
0.010 g±50%
0.10 g±5%
0.25 g±2%
1.00 g±0.5%
10.00 g±0.05%

Treat these figures as the best case. Half the readability is only the rounding of the display; a balance's real uncertainty also includes repeatability, drafts, static and temperature, and is usually larger, which is why balance makers state a minimum sample weight below which a reading should not be trusted. Making a dilution also adds its own two weighings. Use the table to compare weighings with each other, and your balance's specification and your own repeat weighings to decide what is accurate enough. Tolerances for production are discussed in batch weighing tolerance.

Worked example: a trace material

A formula in parts per thousand has a material at 0.5 parts, and you make a 20 g batch.

  • Neat: 20 × 0.5 ÷ 1000 = 0.010 g, ±50% on a 0.01 g balance — not a usable weighing.
  • At 10%: 0.010 ÷ 0.10 = 0.10 g of dilution, ±5%.
  • At 1%: 0.010 ÷ 0.01 = 1.00 g of dilution, ±0.5%.

The 1% dilution makes this weighing accurate. Making and recording dilutions is covered in stock solutions in practice and working with trace materials.

Rounding a formula without losing the total

When you round each line, the total can drift. Three materials at one third each round to 33.33%, which sums to 99.99%. The common practice is to assign the rounding residue to one stated line — often the solvent, or the largest material — and to write that rule in the formula record so anyone can reproduce it. Never let a formula total quietly become 99.99% or 100.01%.

Write what you can weigh

If a calculation gives 0.3333 g and your balance reads to 0.01 g, the weight you can make is 0.33 g, which is 0.0033 g or about 1% less. Write 0.33 g in the batch record, because that is what the batch contains, and keep the exact figure in the formula if you need it for scaling. Errors in batch arithmetic are discussed in perfume batch calculation errors.

Practical exercise: Drill: precision problems

About 40 minutes · You will have: worked answers to three precision problems, checked against the answers given

  1. Problem 1. A 50 g batch contains a material at 0.2%. What is the neat weight, its relative error on a 0.01 g balance, and which dilution would bring the error to about 0.5%?
  2. Problem 2. A 25 g batch contains a material at 2 parts per thousand. Give the neat weight and its error, then the weight and error from a 10% dilution.
  3. Problem 3. Six materials should each be one sixth of a formula. Round to two decimal places, find the residue, and state where you assign it.
  4. Check your answers below.

Answers. 1: 50 × 0.002 = 0.100 g, ±5%; a 10% dilution needs 1.00 g, ±0.5%. 2: 25 × 2 ÷ 1000 = 0.050 g, ±10%; from a 10% dilution, 0.50 g, ±1%. 3: each line rounds to 16.67%, which sums to 100.02%; the residue is −0.02%, assigned to the stated line (for example 16.65% for the largest material or solvent).

You have done this well if your answers match, you state a rounding rule in words, and your batch records show the weights you could actually measure.

Common mistakes

  • False precision. Four decimal places on a 0.01 g balance.
  • Silent drift. A total of 99.99% with no rule.
  • Weighing traces neat. Use a dilution.

Key terms

Rounding residue
The small difference between a rounded formula's total and its intended total, assigned to one stated line.

Knowledge check

1. On a 0.01 g balance, what is the relative rounding error of a 0.25 g weighing?
Show the answer

About ±2%. Half a step is ±0.005 g; 0.005 ÷ 0.25 = 2%.

2. Three materials at one third each round to 33.33%. What do you do with the missing 0.01%?
Show the answer

Assign it to one stated line, such as the solvent or largest material, and record the rule. A stated rule keeps the formula reproducible.

3. Why not write weights to four decimal places on a 0.01 g balance?
Show the answer

You cannot weigh them; the record should show what can be measured. Precision on paper that the balance cannot deliver is false precision.

Written and reviewed by the RUŌOD Lab team. This is general education, not legal, regulatory, medical or safety advice. Example dilutions and exercises are for learning, are not validated products, and have not been safety-assessed. Completing a lesson confers no qualification. How we check these lessons.