Level 3 · Raw Materials and Laboratory Fundamentals

Labeling Dilutions and Samples

A bench lesson: label every dilution, trial and sample so it traces to its record, can be coded for blind tests, and is never mistaken for another.

In short

Every bottle on a perfume bench should say exactly what it is and point back to a record. A dilution needs its material, strength, solvent and date; a trial needs its formula name and version; a sample for blind evaluation needs a neutral code that only your records can decode. This lesson sets out a simple labeling standard and practises it, because unlabeled or half-labeled bottles are how good work becomes unrepeatable.

What you will learn

  • Write a complete label for a dilution and a trial
  • Use codes for blind evaluation without losing traceability
  • Link every label to an entry in your records

Before this lesson: Perfume Dilution Basics: Make Your First 10%

What each label needs

A labeling standard for a small lab. Adapt it, but keep it consistent.
ItemLabel must show
DilutionMaterial, strength (for example 10%), solvent, date made, your initials, source lot if known
Accord or trialName, version, date, a reference to the formula record
Blind sampleA neutral code only; the key is in your records
Finished test batchName, version, batch code, concentration, date
Waste"Waste", contents in general terms, date

The Lab's guides to keeping a perfume lab notebook and batch numbers and lot codes describe the records the labels point to.

Codes for blind evaluation

Blind tests need labels that give nothing away. Use random three-digit codes rather than A, B and C, which suggest an order, and never write the real name anywhere a tester could see it. Record the key — which code is which sample — in your notebook before the test starts, so that nothing depends on memory. After the test, keep the key with the results; a result without its key is useless.

Strength and solvent are not optional

A bottle marked "indole" that actually holds indole at 1% in DPG will be weighed into a formula as if it were neat, and every calculation after that will be wrong. The strength and solvent on the label are what make the amount in your record mean something; see how to dilute aroma chemicals.

Practical points

  • Use labels that survive solvent. Ethanol and many materials dissolve ink; test your labels and pens.
  • Label the bottle, not the cap. Caps get swapped.
  • Write hazard information when a dilution is still hazardous, following the SDS; a 10% dilution of a flammable or irritant material may still be both.
  • Write standard operating procedures so everyone labels the same way; see perfume lab SOPs.

Practical exercise: Practice: label a dilution set and a blind trial

About 30 minutes · You will have: a labeled dilution ladder and a set of coded samples, each traceable to a record entry

  1. Make a 10%, 1% and 0.1% dilution ladder of one material, and label each bottle to the standard above.
  2. Enter each dilution in your records with the same details.
  3. Prepare three samples of one composition for a blind test, label them with random three-digit codes, and record the key.
  4. Ask a partner to pick any bottle and trace it to its record using only the label.
  5. Note anything your partner could not find and fix the standard.

You have done this well if your partner could trace every bottle to its record from the label alone, no coded sample revealed its identity, and every dilution's strength and solvent are on both the label and the record.

Common mistakes

  • Labeling the cap. Caps move between bottles.
  • Codes that hint at the answer. Use random codes.
  • Ink that dissolves. Test labels with your solvent first.

Safety

  • Follow each material's SDS for hazard labeling of dilutions, and store labeled waste safely until disposal.

Key terms

Traceability
Being able to follow any bottle back to the record that says what it is, how it was made and from which lots.
Sample code
A neutral label used in place of a name so that a sample can be evaluated without bias.

Knowledge check

1. What must a dilution label always state?
Show the answer

Material, strength, solvent and date. Without strength and solvent, the dilution cannot be used in a formula correctly.

2. How do you keep coded samples traceable?
Show the answer

Record the code key in your notebook or file before testing. The key must exist, but not where testers can see it.

3. Why date a dilution?
Show the answer

Dilutions change with age and evaporation. The date tells you when to check or remake it.

Written and reviewed by the RUŌOD Lab team. This is general education, not legal, regulatory, medical or safety advice. Example dilutions and exercises are for learning, are not validated products, and have not been safety-assessed. Completing a lesson confers no qualification. How we check these lessons.